This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module. ESP8266 ESP-12F Features: ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3 All pins lead out, is not connected nor occupy by Arduino IO port ESP-12F can work as slave mode for arduino, or program […]
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module.
ESP8266 ESP-12F Features:
ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3
All pins lead out, is not connected nor occupy by Arduino IO port
ESP-12F can work as slave mode for arduino, or program independently.
ADC and ADC external voltage port lead out.
On board PROG programmable button, and ESP reset button.
Demo code inlcudes manipulating AT commands to transiceive data from web, find in the wiki documentaion link below.
Can be used independently, can be connected to a standard serial communication FTDI
Lora Module SX1278/76:
Reserved but not place module.
D10 default used for lora chip select pin.
D5-D7 can connect via jumper to D1, D2, D5 lora DIO pins.
D2 default used for lora IRQ DIO0 pin.
Antenna not connected default, support pin, ipex, or sma type connector, suit your needs.
All lead out DIO D0 ~ D5 pins on side.
Addon:
Extra DH11 socket, with 10K pull-up data pin.
Packaging:
Only include the main board with esp-12F as red board.
Not include any pin headers, lora module, antenna.
Arduino pin header please buy alone here.
the last image of the green board indicates the final soldered state only.
Documentation please see on this page.
This TTGO Board Combines ESP32, LoRa Radio, and OLED Display for
2pcs/lot Lora611PRO 915MHz 5Km sx1276/sx1278 AES encrypted MESH
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module., ESP8266 ESP-12F Features:, ESP-12F serial to Arduino serial,
LORA WIFI RF Arduino Shield, ESP8266 SX1278
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
Portenta Vision Shield - LoRa® — Arduino Online Shop
The D1 mini Pro is a mini wifi board based on ESP-8266EX., Key Factors:, Upgrade to use CP2104 USB-TTL and 16MB flash., Due to chip limitation,
D1 Pro Mini DEV Board, Based on ESP8266ex Chip
LORA WIFI RF Arduino Shield, ESP8266 SX1278 - ElectroDragon
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
ESP32 Core, Support arduino IDE, auto install boards in IDE called ESP lora 32., 600DMIPS, 32Mbit, Tensilica LX dual core, WIFI 802.11
Wifi Lora ESP32 Dev. Board
Lora Technology please see introduction and features here., General Features:, Using PE4259 RF switch, enhance performance and reduce the
Lora RF Wireless Transceiver EE1, 100mW [Freq]
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
Features, ESP-WROOM-02 is a low-power 32-bit MCU Wi-Fi module, based on the ESP8266 chip. TCP/IP network stacks, 10-bit ADC, and
WROOM-02 WIFI Module, ESP8266, 4MB [D/U]
ESP8266 ESP-12F Wifi development board, Breadboard compatible, Pin headers are included but needed to be soldered by yourself, Left and right side
D1 Mini WIFI Dev Board, ESP8266 ESP-12F
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor